How to Ship Stained Glass
By [http://EzineArticles.com/expert/David_Gomm/20692]David Gomm
To ship a piece of glass, it needs to be crated. We build a crate around every piece of glass which we ship. It needs to be a custom fit so that the glass can be adequately protected. The following pictures are of us building a crate for a 3' by 5' window. We use the same techniques when crating a smaller window.
By building a custom crate for each piece of glass that you plan to ship, you will have better success shipping glass across country. You will find that by building a crate in the following manner that you will be able to ship small windows using common carriers like UPS or Fedex.
We have the stained glass panel laid out on a different table than the one we're going to build the crate on.
First we lay the 1" thick rigid foam insulation on the table. This comes in pink or blue depending on the brand you buy.
We lay the panel to be shipped on top of the insulation and use a box knife to cut around the panel. We cut right on the edge. We don't want any extra foam hanging beyond the window edge.
Then we slide the cut line of the foam over the edge of the table and push down to break the foam. If it has a membrane holding it together, we run a utility knife along it to cut it off. We use the cut off pieces as a template to cut the second piece of foam the same size as the first.
Then we take a two by four and use it as a pattern to cut four pieces of filler pieces of foam.
Here we have the "foam, glass, foam sandwich," with some of our cut pieces laying on top.
Next we take the long pieces and cut them to the length of the sign and set one on each side of the sign. Then we stand up a two by four along the long edge and mark a cut line a two by four width from the end of the sign.
(We make sure that the other end of the two by four is hanging out a two by four width at the other end when marking) The cut two by four is then cut a saw blade width short so the box will keep the foam tight. We cut a second one for the other side.
Here is the foam "sandwich" with another piece of scrap foam on top of the pile to raise the top of the entire package to the height of the two by four frame. You can also see the two by four side piece ready to be put in place.
Now we use a clamp to pull the two by fours together on each end. We only apply a slight amount of pressure to the clamp. We want the crate to be tight but not so tight we damage the foam and drive it into the stained glass we're protecting.
We cut and attach our connecting two by fours. Then we check that the top of the crate is even with the two by four framework. Then we add a couple of layers of foam blanket to the top so that the lid of the crate will apply a slight amount of pressure when it's in place.
Because we have an inch of foam on the top and bottom and all around the glass inside the crate, it is safe to screw down the plywood top of the crate. We laid the plywood on top of the framework and traced around it and then cut it out.
Next we got some friends to help flip the whole assembly over.
Then we laid the final piece of plywood down and screwed it in place.
When we ship, we find that moving van lines have a good system in place to haul sensitive and delicate items, such as electronics and stained glass. They cost 3 or 4 times more than common carrier, but you get what you pay for.
We took pictures for this article that can be viewed at [http://www.betterstainedglass.com/Newsletter/Archives/5-07-2005julyhow2ship/july2005how2ship.htm]http://www.betterstainedglass.com/Newsletter/Archives/2005julyhow2ship/july2005how2ship.htm
David Gomm started building stained glass windows professionally back in 1983 and has become an expert at many aspects of stained glass building, design and repair. He writes a monthly newsletter at his better stained glass website.
Article Source: [http://EzineArticles.com/?How-to-Ship-Stained-Glass&id=239997] How to Ship Stained Glass